Home › Machines › xTool P2 / P2S (55W)
xTool P2 / P2S (55W) specs, bed size and cutting speeds
The xTool P2 / P2S (55W) is a CO2 50–60 W laser with a 600 × 308 mm work area. Below: full specs, real cutting speeds by material, and what a part costs in machine time. Drop your SVG, DXF or PDF to price your own file — it runs entirely in your browser and nothing is uploaded.
Open the calculator for the xTool P2 / P2S (55W) →xTool P2 / P2S (55W) specs
| Laser type | CO2 (10,600 nm) |
|---|---|
| Power class | CO2 50–60 W |
| Bed size (work area) | 600 × 308 mm |
| Work area (inches) | 23.6 × 12.1 in |
| Cuts | clear and opaque acrylic, plywood, MDF, card, leather, fabric |
| Approx. price | ~€4,000 (machine only, August 2026 — from our xTool vs Glowforge comparison) |
xTool P2 / P2S (55W) cutting cost examples
Machine time and price for a 100 × 60 mm part (320 mm of cutting) at €60/h, by material:
| Material | Speed | Time | Price |
|---|---|---|---|
| Plywood 3 mm | 13 mm/s | 25 s | €0.41 |
| MDF 3 mm | 14.3 mm/s | 22 s | €0.37 |
| Acrylic 3 mm | 11.7 mm/s | 27 s | €0.46 |
| Cardboard 3 mm | 22.8 mm/s | 14 s | €0.23 |
These scale from real workshop speeds. Your parts differ — open the calculator and drop your file or enter your size for an exact figure. You can also switch to engraving.
What this machine physically cannot do
This is a CO2 laser at 10.6 µm, the wavelength organic materials absorb best. It cuts clear cast acrylic to a flame-polished edge, which no diode can do at any power, and it handles wood, leather, card, fabric and rubber faster and more cleanly than a diode of similar nominal wattage.
It cannot mark bare metal without a coating spray such as CerMark — for bare steel or aluminium you want a fiber laser. It also must not be pointed at PVC, vinyl or anything chlorine-bearing: the gas produced corrodes the mirrors, rails and electronics, and is dangerous to breathe.
The trade-off against a diode is maintenance. A CO2 machine has mirrors that need alignment, a tube that is a consumable with a finite life, and usually a water cooling loop to look after.
What fits, and what it is like to live with
The bed is 600 × 308 mm. In practice that means it takes an A3 sheet flat, and you can nest roughly 18 100 mm coaster blanks in a single run before you have to reload.
The workshop standard. This is the class most small production shops settle on: 5–6 mm acrylic and plywood in one pass, fast engraving, and enough life in the tube to run daily. If you are buying one machine to do everything, it is almost always this one.
xTool P2 / P2S (55W) FAQ
How fast does the xTool P2 / P2S (55W) cut 3 mm plywood?
About 13 mm/s. Cutting a 100 × 60 mm part (320 mm of cut) takes roughly 25 s of machine time on the xTool P2 / P2S (55W).
Can the xTool P2 / P2S (55W) cut clear acrylic?
Yes. The xTool P2 / P2S (55W) is a CO2 laser (10,600 nm) and cuts both clear and opaque acrylic, plus plywood, MDF, leather, card and fabric.
What is the xTool P2 / P2S (55W) bed size?
The xTool P2 / P2S (55W) has a 600 × 308 mm work area (23.6 × 12.1 inches). That is the largest part it can cut in one pass without repositioning the material.
How much does it cost to run the xTool P2 / P2S (55W)?
Laser cutting is priced by machine time: cut length ÷ cutting speed × passes = time, then time × hourly rate + setup. At €60/h a 100 × 60 mm plywood part costs about €0.41. Use the calculator to price your own file.
How much does the xTool P2 / P2S (55W) cost?
~€4,000 as of August 2026, for the machine alone. Budget extra for extraction, a decent air assist and material. Street prices move, so treat this as a starting point and check the seller before you quote work on it. Full reasoning in our xTool vs Glowforge comparison.
Where to buy the xTool P2 / P2S (55W)
Prices move often — check current offers before you quote jobs on a machine you don't own yet.
xTool official store ↗ Check price on Amazon ↗
Some links are affiliate links: if you buy through them we may earn a small commission at no extra cost to you. It keeps this calculator free.
Machines similar to the xTool P2 / P2S (55W)
Comparable on speed, bed size and material capability — the specs side by side:
- OMTech Polar / Polar+ (55W) — CO2 50–60 W, 500 × 300 mm, 13 mm/s in 3 mm plywood. similar class
- Glowforge Basic / Plus / Pro — CO2 40–45 W, 495 × 279 mm, 12 mm/s in 3 mm plywood. similar class
- OMTech / Gweike 60W — CO2 50–60 W, 600 × 400 mm, 15 mm/s in 3 mm plywood. similar class
Or see the full machine list and the complete speed table.
← All machine calculators · Full speed table · Main calculator