Home › Machines › Epilog Fusion Pro
Epilog Fusion Pro specs, bed size and cutting speeds
The Epilog Fusion Pro is a Professional CO2 laser with a 812 × 508 mm work area. Below: full specs, real cutting speeds by material, and what a part costs in machine time. Drop your SVG, DXF or PDF to price your own file — it runs entirely in your browser and nothing is uploaded.
Open the calculator for the Epilog Fusion Pro →Epilog Fusion Pro specs
| Laser type | CO2 (10,600 nm) |
|---|---|
| Power class | Professional CO2 |
| Bed size (work area) | 812 × 508 mm |
| Work area (inches) | 32.0 × 20.0 in |
| Cuts | clear and opaque acrylic, plywood, MDF, card, leather, fabric |
Epilog Fusion Pro cutting cost examples
Machine time and price for a 100 × 60 mm part (320 mm of cutting) at €60/h, by material:
| Material | Speed | Time | Price |
|---|---|---|---|
| Plywood 3 mm | 20 mm/s | 16 s | €0.27 |
| MDF 3 mm | 22 mm/s | 15 s | €0.24 |
| Acrylic 3 mm | 18 mm/s | 18 s | €0.30 |
| Cardboard 3 mm | 35 mm/s | 9 s | €0.15 |
These scale from real workshop speeds. Your parts differ — open the calculator and drop your file or enter your size for an exact figure. You can also switch to engraving.
What this machine physically cannot do
This is a CO2 laser at 10.6 µm, the wavelength organic materials absorb best. It cuts clear cast acrylic to a flame-polished edge, which no diode can do at any power, and it handles wood, leather, card, fabric and rubber faster and more cleanly than a diode of similar nominal wattage.
It cannot mark bare metal without a coating spray such as CerMark — for bare steel or aluminium you want a fiber laser. It also must not be pointed at PVC, vinyl or anything chlorine-bearing: the gas produced corrodes the mirrors, rails and electronics, and is dangerous to breathe.
The trade-off against a diode is maintenance. A CO2 machine has mirrors that need alignment, a tube that is a consumable with a finite life, and usually a water cooling loop to look after.
What fits, and what it is like to live with
The bed is 812 × 508 mm. In practice that means it takes a 600 × 400 mm hobby sheet flat, and you can nest roughly 40 100 mm coaster blanks in a single run before you have to reload.
You are paying for reliability and support, not raw wattage. A machine in this class holds its calibration over thousands of hours, comes with a real service contract, and has the motion quality to engrave fine detail repeatably. Compared with a hobby CO2 machine of similar wattage it will not cut dramatically faster — it will simply still be doing it, to the same tolerance, in three years.
Epilog Fusion Pro FAQ
How fast does the Epilog Fusion Pro cut 3 mm plywood?
About 20 mm/s. Cutting a 100 × 60 mm part (320 mm of cut) takes roughly 16 s of machine time on the Epilog Fusion Pro.
Can the Epilog Fusion Pro cut clear acrylic?
Yes. The Epilog Fusion Pro is a CO2 laser (10,600 nm) and cuts both clear and opaque acrylic, plus plywood, MDF, leather, card and fabric.
What is the Epilog Fusion Pro bed size?
The Epilog Fusion Pro has a 812 × 508 mm work area (32.0 × 20.0 inches). That is the largest part it can cut in one pass without repositioning the material.
How much does it cost to run the Epilog Fusion Pro?
Laser cutting is priced by machine time: cut length ÷ cutting speed × passes = time, then time × hourly rate + setup. At €60/h a 100 × 60 mm plywood part costs about €0.27. Use the calculator to price your own file.
Where to buy the Epilog Fusion Pro
Prices move often — check current offers before you quote jobs on a machine you don't own yet.
Epilog official store ↗ Check price on Amazon ↗
Some links are affiliate links: if you buy through them we may earn a small commission at no extra cost to you. It keeps this calculator free.
Machines similar to the Epilog Fusion Pro
Comparable on speed, bed size and material capability — the specs side by side:
- Trotec Speedy 300 / 360 / 400 — Professional CO2, 726 × 432 mm, 20 mm/s in 3 mm plywood. similar class
- OMTech / Thunder / Gweike 80W — CO2 80–100 W, 700 × 500 mm, 18 mm/s in 3 mm plywood. similar class
- GCC LaserPro Spirit / Mercury — Professional CO2, 860 × 610 mm, 18 mm/s in 3 mm plywood. similar class
- Aeon Nova 10 / 14 — Professional CO2, 1400 × 900 mm, 22 mm/s in 3 mm plywood. about 1.1× the cutting speed
Or see the full machine list and the complete speed table.
← All machine calculators · Full speed table · Main calculator