Home › Machines › Aeon Nova 10 / 14
Aeon Nova 10 / 14 specs, bed size and cutting speeds
The Aeon Nova 10 / 14 is a Professional CO2 laser with a 1400 × 900 mm work area. Below: full specs, real cutting speeds by material, and what a part costs in machine time. Drop your SVG, DXF or PDF to price your own file — it runs entirely in your browser and nothing is uploaded.
Open the calculator for the Aeon Nova 10 / 14 →Aeon Nova 10 / 14 specs
| Laser type | CO2 (10,600 nm) |
|---|---|
| Power class | Professional CO2 |
| Bed size (work area) | 1400 × 900 mm |
| Work area (inches) | 55.1 × 35.4 in |
| Cuts | clear and opaque acrylic, plywood, MDF, card, leather, fabric |
Aeon Nova 10 / 14 cutting cost examples
Machine time and price for a 100 × 60 mm part (320 mm of cutting) at €60/h, by material:
| Material | Speed | Time | Price |
|---|---|---|---|
| Plywood 3 mm | 22 mm/s | 15 s | €0.24 |
| MDF 3 mm | 24.2 mm/s | 13 s | €0.22 |
| Acrylic 3 mm | 19.8 mm/s | 16 s | €0.27 |
| Cardboard 3 mm | 38.5 mm/s | 8 s | €0.14 |
These scale from real workshop speeds. Your parts differ — open the calculator and drop your file or enter your size for an exact figure. You can also switch to engraving.
What this machine physically cannot do
This is a CO2 laser at 10.6 µm, the wavelength organic materials absorb best. It cuts clear cast acrylic to a flame-polished edge, which no diode can do at any power, and it handles wood, leather, card, fabric and rubber faster and more cleanly than a diode of similar nominal wattage.
It cannot mark bare metal without a coating spray such as CerMark — for bare steel or aluminium you want a fiber laser. It also must not be pointed at PVC, vinyl or anything chlorine-bearing: the gas produced corrodes the mirrors, rails and electronics, and is dangerous to breathe.
The trade-off against a diode is maintenance. A CO2 machine has mirrors that need alignment, a tube that is a consumable with a finite life, and usually a water cooling loop to look after.
What fits, and what it is like to live with
The bed is 1400 × 900 mm. In practice that means it takes a full 1220 × 610 mm half-sheet flat, and you can nest roughly 126 100 mm coaster blanks in a single run before you have to reload.
You are paying for reliability and support, not raw wattage. A machine in this class holds its calibration over thousands of hours, comes with a real service contract, and has the motion quality to engrave fine detail repeatably. Compared with a hobby CO2 machine of similar wattage it will not cut dramatically faster — it will simply still be doing it, to the same tolerance, in three years.
Aeon Nova 10 / 14 FAQ
How fast does the Aeon Nova 10 / 14 cut 3 mm plywood?
About 22 mm/s. Cutting a 100 × 60 mm part (320 mm of cut) takes roughly 15 s of machine time on the Aeon Nova 10 / 14.
Can the Aeon Nova 10 / 14 cut clear acrylic?
Yes. The Aeon Nova 10 / 14 is a CO2 laser (10,600 nm) and cuts both clear and opaque acrylic, plus plywood, MDF, leather, card and fabric.
What is the Aeon Nova 10 / 14 bed size?
The Aeon Nova 10 / 14 has a 1400 × 900 mm work area (55.1 × 35.4 inches). That is the largest part it can cut in one pass without repositioning the material.
How much does it cost to run the Aeon Nova 10 / 14?
Laser cutting is priced by machine time: cut length ÷ cutting speed × passes = time, then time × hourly rate + setup. At €60/h a 100 × 60 mm plywood part costs about €0.24. Use the calculator to price your own file.
Where to buy the Aeon Nova 10 / 14
Prices move often — check current offers before you quote jobs on a machine you don't own yet.
Aeon Laser official store ↗ Check price on Amazon ↗
Some links are affiliate links: if you buy through them we may earn a small commission at no extra cost to you. It keeps this calculator free.
Machines similar to the Aeon Nova 10 / 14
Comparable on speed, bed size and material capability — the specs side by side:
- Industrial CO2 130–150W — CO2 130 W+, 1300 × 900 mm, 24 mm/s in 3 mm plywood. similar class
- Epilog Fusion Pro — Professional CO2, 812 × 508 mm, 20 mm/s in 3 mm plywood. similar class
- Trotec Speedy 300 / 360 / 400 — Professional CO2, 726 × 432 mm, 20 mm/s in 3 mm plywood. similar class
Or see the full machine list and the complete speed table.
← All machine calculators · Full speed table · Main calculator