Home › Guides › Nesting for laser cutting: how to fit more par…

Nesting for laser cutting: how to fit more parts on a sheet (and pay less)

A laser cutting a sheet of plywood on a honeycomb bed

Nesting means arranging all your parts on one sheet so little material is wasted. A tight layout can drop the number of sheets in a job, and sheets are the biggest line on many quotes. This guide covers the nesting file, gap rules, the yield arithmetic, free tools and how to hand a shop a file it will accept.

What a nesting file is

A nesting file is the layout. It is a DXF or SVG that places every part on a sheet at its final position, at 1:1 scale. The laser follows it line by line. Nothing else is needed to cut.

Some shops build the nest for you from your single-part files. Others ask you to send one. Either way, the nest decides how many sheets the job uses. If you already know the sheet size, you can save a round of emails by nesting first.

There are two ways to place parts next to each other:

Kerf and part spacing

Kerf is the width of material the beam removes. Typical values are 0.1–0.3 mm for CO2 and diode lasers on wood and acrylic, and 0.1–0.2 mm for a fiber laser on thin steel. It changes with power, speed, focus and thickness.

Kerf matters for nesting in two ways. It eats into the gap between parts, and it makes each part slightly smaller than drawn. A gap that is too small leaves a thin web that burns through, chips or warps.

MaterialGap between partsEdge margin
Wood, MDF, acrylic2–3 × thickness, minimum 3 mm5–10 mm
Sheet metal (fiber)1–2 × thickness5–10 mm

These are rules of thumb. Thick or heat-sensitive stock needs more room. Always follow the shop's own minimums if they publish them.

To find your own kerf, see our laser kerf calculator. The joinery guide also shows how to measure it with test squares: laser-cut joinery and kerf.

Yield math: how many parts fit

You do not need software to estimate a nest. Use a grid count first.

Take a 600 × 400 mm sheet, 95 × 95 mm square parts, a 3 mm gap and a 5 mm edge margin on every side. Usable area is 590 × 390 mm.

The formula is: columns = floor((sheet width − 2 × margin + gap) / (part width + gap)).

Check it: six parts and five gaps take 6 × 95 + 5 × 3 = 585 mm, which fits in 590. Four parts and three gaps take 389 mm, which fits in 390. It is a tight fit, so a margin of 6 mm would drop you to 3 rows. Small numbers matter.

Rotating a square by 90° changes nothing. Rotation helps with rectangles. A 95 × 60 mm part, for example, can sit long-side along either edge of the sheet. Try both and keep the better count.

Yield is part area divided by sheet area. Here: 24 × 95 × 95 = 216,600 mm² over 240,000 mm² is about 90 %. Squares are the easy case. Real jobs with mixed shapes, holes and slots usually land lower: a plain rectangular grid gives roughly 55–75 %, and a good nest gets 75–85 %.

Round parts show why offset rows can pay off. Take 60 mm circles with the same gap and margin:

That is 11 % more parts from the same sheet. It does not always work: with 95 mm circles on this sheet, offset rows give 22, fewer than the grid's 24. Count both. To skip the arithmetic, use the sheet yield calculator.

Free nesting tools

You can nest without paying for software. Each tool below suits a different job.

For boxes, plates and brackets, a bounding-box nest is often within a few percent of true-shape. For organic or curved parts, try Deepnest and let it run.

How nesting changes a laser cutting quote

Shops charge material per sheet, or per area used, plus machine time and setup. Nesting hits the first one hardest.

Machine time barely changes, because the cut length is much the same. The exception is shared-line cutting. When two straight edges become one cut, you remove duplicate lines. On rectangular parts this can reduce cut time by roughly 10–30 %.

Sheet count drives the quote. Say you need 120 parts:

One sheet fewer. On an €8–€15 sheet, that saves €8–€15 in material, plus the handling and cutting time for the sheet you no longer use. On larger runs or costly stock the gap grows quickly.

For a full picture of what else goes into the price, read how much laser cutting costs, or try the laser cutting cost calculator.

Preparing a nesting file a shop will accept

  1. Scale 1:1, units in mm. Check one known dimension after export.
  2. Closed paths. Open outlines confuse the cut order and may be skipped.
  3. Remove duplicate lines. Two lines on top of each other get cut twice, burn the edge and add time.
  4. Use layers. Keep cut, engrave and score on separate layers or colours, and say which is which.
  5. One sheet per file or page. Do not stack several sheets in one drawing.
  6. Label parts. A small engraved number on each part makes sorting easy.
  7. Keep the margin. Stay inside the shop's usable area, not the nominal sheet size.

Send the single-part files too. If your nest does not suit the shop's machine, they can re-nest quickly.

Common nesting mistakes

FAQ

What is a nesting file for laser cutting?

A nesting file is a DXF or SVG layout that places every part on a sheet at its final position and at 1:1 scale. The laser cuts exactly what is in the file. A good nest uses the sheet well, so fewer sheets are needed. Some shops make the nest for you, others ask you to send one.

Is there free nesting software for laser cutting?

Yes. Deepnest is a free, open-source desktop app that handles irregular shapes. SVGnest runs in the browser. Inkscape can build simple grids with tiled clones. Our free online tool nests rectangles in your browser without uploading the file. Metal shops usually use paid CAM such as SigmaNEST or ProNest.

How much space should I leave between laser-cut parts?

For wood and acrylic, leave 2–3 times the material thickness, with a minimum of about 3 mm. For sheet metal, 1–2 times the thickness is typical. Keep 5–10 mm from the sheet edge. Thick or heat-sensitive material needs more room, so check the minimums your shop publishes.

Does nesting reduce laser cutting cost?

Usually yes, through material. A tighter nest can cut the number of sheets, and sheet count drives most quotes. Machine time changes little, except with shared-line cutting on rectangular parts, which can cut time by roughly 10–30 percent. The saving depends on the shop's pricing method.

Can I nest parts myself before sending a quote request?

Yes, and it helps. Ask for the usable sheet size, then nest at 1:1 scale in mm with the shop's gap and margin. Use a free tool or a simple grid count. Send both the nest and the single-part files, so the shop can re-nest if its machine needs a different layout.

← All guides · Price your file · By machine